HD/SD-SDI Dual Non-Reclocking Distribution Amplifier (2 - 1 x 4)

Model: 500DA2Q-HD

Normal mode for SMPTE ST 292-1 (1.5Gb/s) SMPTE ST 259 (143 to 360Mb/s) or SMPTE ST 344 (540Mb/s) signals - autodetects correct bit rate
Jumper selectable mode for DVB-ASI
Jumper selectable non-reclock mode for SMPTE ST 310(19.4Mb/s) signals or any other SDI signal within the 143Mb/s to 1.5Gb/s range
Configurable as 1 DA with 8 outputs or 2 DAs with 4 outputs each
Fully hot-swappable from front of frame with no BNC disconnect required

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The Evertz 500DA2Q-HD Dual HD Reclocking Distribution Amplifier provides the highest density DA in the industry allowing up to 32 HD or SDI Distribution amplifiers in a 3RU rack space. It provides inexpensive distribution of your SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259 (143 to 360Mb/s), SMPTE ST 344 (540Mb/s), DVB-ASI or SMPTE ST 310 (19.4Mb/s) or any other SDI signal within the 143Mb/s to 1.5Gb/s range. The 500DA2Q-HD features two auto-equalized inputs and can be configured either as a single DA with eight reclocked outputs or as two separate DAs with four outputs each. In the case of dual operation, each DA can be individually set via jumpers for either reclocking or non-reclocking. The 500DA2Q-HD is housed in the 500FR frame that will hold up to 16 modules.

Normal mode for SMPTE ST 292-1 (1.5Gb/s) SMPTE ST 259 (143 to 360Mb/s) or SMPTE ST 344 (540Mb/s) signals - autodetects correct bit rate
Jumper selectable mode for DVB-ASI
Jumper selectable non-reclock mode for SMPTE ST 310(19.4Mb/s) signals or any other SDI signal within the 143Mb/s to 1.5Gb/s range
Configurable as 1 DA with 8 outputs or 2 DAs with 4 outputs each
Fully hot-swappable from front of frame with no BNC disconnect required
Independent isolated output drivers to ensure no cross channel loading effects (i.e. no need to terminate unused outputs)
Module health and 2x4 Mode Status LEDs
Reclocker(s) Locked, Carrier Present and Video Standard LEDs for each DA channel
Tally output on Frame Status bus upon loss of input signal
VistaLINK® capable for remote monitoring via SNMP (using VistaLINK® PRO) when installed in 500FR frame with 500FC VistaLINK® Frame Controller
2 inputs
SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259 (143 to 360Mb/s), SMPTE ST 344 (540Mb/s), DVB-ASI or SMPTE ST 310(19.4Mb/s)
Auto equalization to 100m Input A, 90m Input B (Belden 1694A) @ 1.5Gb/s
4 Reclocked Outputs per Input
Jitter < 0.2UI
Card Edge LED's: Module Health Status, 2x4 mode operation, Reclocker Rate detections, Reclocker Locked, Carrier Present

Spec Sheet available - Yes

Standard (Reclocked): SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259 (143 to 360Mb/s), SMPTE ST 344 (540Mb/s), DVB-ASI
Standard (Non-Reclocked): SMPTE ST 310 (19.4Mb/s), any signal in the 143Mb/s to 1.5Gb/s range
Number of Inputs: 2
Connector: BNC per IEC 61169-8 Annex A
Equalization (Input A): Automatic to 100m @ 1.5Gb/s with Belden 1694A or equivalent cable
Equalization (Input B): Automatic to 90m @ 1.5Gb/s with Belden 1694A or equivalent cable
Return Loss: > 10dB up to 1.5Gb/s
Number of Outputs: Mode set by jumper
2x4 Mode: 4 Reclocked from each input. Reclockers can be bypassed separately for each input
1x8 Mode: 8 Reclocked from Input A (1). Reclockers can be bypassed
Signal Level: 800mV nominal
DC Offset: 0V ±0.5V
Rise and Fall Time: 200ps nominal
Overshoot: < 10% of amplitude
Jitter: < 0.2UI
Voltage: +12V DC
Power: 6 Watts
EMI/RFI: Complies with FCC Part 15 Class A, EU EMC Directive
Number of Slots: 1

HD/SD SDI Dual Reclocking & Non-reclocking Distribution Amplifier 56 kb - Data Sheet

Project List

AV-iQ Terms and Conditions | | Powered by AV-iQ

bottom of page